Electronic Toys Inspection Services

Our Main Service Pre-shipment Inspection(PSI) During production Inspection (DPI) Container Loading Supervision(CLS) Factory Audit (FA) Simple Factory Audit (SFA) Social Compliance Audit (SA/Sedex) Laboratory Testing Product Certification Sample Check How to check the electronic toys Open 3...

Send InquiryChat Now

Product Details

图片6.jpg

Our Main Service

 

Pre-shipment Inspection(PSI)
blob.png

During production Inspection (DPI)blob.png

Container Loading Supervision(CLS)

blob.png

Factory Audit (FA)

blob.png

Simple Factory Audit (SFA)

blob.png

Social Compliance Audit (SA/Sedex)        blob.png

Laboratory Testing

blob.png

Product Certification

blob.png

Sample Checkblob.png

TIM图片20180518142235.jpg

How to check the electronic toys

Open 3 cartons and count the quantity inside - should match the spec and shipping marks.

Check the item for any strong or offensive odors

Each product should work normally as per claimed

Use 3M tape for testing; Logos and other marking should not peel off.

According to EN71-1 (8.11 and 8.12)

F > 90N/10sec.

Product should get assembled correctly and easily, and stable/functional after building.

According to EN71-1 (8.4.2.2)

F > 90N/10sec.

According to EN71-1 (5.2) 

(no hard or sharp contaminants, such as metal particles, nails, needles and splinters)


(A)For USA market: Reach to the required tension force within 5S, then hold 10S:

(1) 0 ≤18Months: 10 lb; 

(2) 18Months to 36Months: 15 lb;

(3) 36Months to 96Months: 15 lb. The seam should not be opened and the inside small part should not be accessible    after test.                                 

(B)For Europe market, 

(1)Use clamps with jaws to which 19mm dia. washers are affixed.

(2)Attach the clamps in the most onerous place on the casing not less than 30mm apart and equidistant to the seam.   Ensure there is sufficient material for full clamping by the 19 mm disc jaws.                       

(3)Apply a force between the 2 clamps of 70N+/-2N gradually within a period of 5s. Maintain the force 10s. Apply     the test to this area of casing or seam only once.Fail for: The seam is opened under 70N.


F>90N/10sec.

According to EN71-1 (8.4.2.1) (nose, eye of the plush, buttons…..)

(A)For USA market, reach to the required tension force within 5S, then hold 10S: 

  (1)0 ≤18 Monthes:10 lbs;

  (2)18 Months to 36 Monthes:15 lbs;

  (3)36 Months to 96 Monthes:15 lbs. The tested parts should not be broken and detached, there should not be small     parts or sharp points.                     

(B)For Europe market, reach to the required tension force within 5S, then hold 10S: 

  (1)0 ≤ 36Months:50 N(D<6 mm); 

  (2)0 ≤ 36Months: 90 N (D>6 mm).There should not be sharp edge, sharp point or small part after test.

    Reached to the required torque force within 5S, then hold 10S:                      

1.plastic:0 to ≤36M:0.34 Nm                      

2.soft: 180degrees. There should not be sharp edge, sharp point or small part after test.

Hot Tags

Hot Tags: electronic toys inspection services, in China, in Asia, professional, advanced
Related Products

Inquiry

  • *Your Name:
  • *E-mail:
  • Content: